Technical Specifications
Technical Specifications
Casting Material
316L Stainless Steel
Weight
Stainless:
Dual Nozzle | 25 lbs. | 11.35 kg. |
Triple Nozzle | 26 lbs. | 11.80 kg. |
Height
12 ¼ in 31.12 cm
Minimum Tank Opening (Inside Diameter)
Dual Nozzle | 6 ¼ in. | 15.88 cm. |
Triple Nozzle | 10 ¼ in. | 26.04 cm. |
Inlet Connection
ID= 2” NPT, Female Threads, 11.5 tpi
OD= 2 ½” Quick Disconnect Coupling
Cam Locking Type
OR
2 ½” NH, Male Threads, 7.5 tpi
Rotor Shaft
Stainless Steel substrate is plasma flame
sprayed with Chromium Oxide, then ground to finish
dimension. The final product is a hard, dense surface that is
resistant to abrasive wear, high temperatures and chemical
corrosion. The smooth surface also lends itself to sealing
with rotary seals. The thrust imparted on the rotor shaft is
distributed by a tungsten carbide thrust washer fastened
to the rotor shaft pinion gear. Carbide is an excellent wear
material and has very high corrosion resistance.
Main Bearings
The main bearings that support the rotation
of the Tee Housing and Nozzle Housing are composed of
a carbon fiber reinforced thermoplastic material, with 15%
PTFE for lubricant. These bearings have an extremely
low coefficient of thermal expansion, and both a low water
absorption and wear factor. Ball bearings have been
eliminated by the use of this bearing material.
Operating pressure / gpm range
40 – 350 psi | 2.81 – 24.61 kg /cm |
30 – 300 gpm | 1.89 – 18.92 ltr / sec |
Temperature Range
up to 250 F (121 C)
Seals
Static seals (o-rings) are compounded for extended
use in various tank cleaning applications. Several different
types of o-rings are available to suit specific tank cleaning
environments. Dynamic seals (which seal rotating parts)
are specially designed spring or pressure seals. The jacket
material is a Teflon alloy which increases wear life and
corrosion resistance.
Geartrain
The internal gearbox reduction is achieved
using a spur gear system, and is available in two gear
ratios: 655: 1 and 273: 1. Switching from one ratio to
the other is achieved by simply changing 2 of the 5
interchangeable stainless steel gearsets available.
Geartrain Lubrication
Two types of lubrication are
available; sealed gearbox with food grade gear oil or
flow-thru gearbox; where the cleaning solution lubricates
the gears. Gearbox Qty = 14oz. (414 ml.) SAE 90. See
preventative maintenance, page 2 for specific types of oil.
Nozzle Housing Drive
Pin drive or clutch drive is
available. Pin drive is recommended for CIP applications,
while the clutch drive is recommended for portable use,
where the machine will be handled often.
CIP Applications
Several self cleaning features are
built into all machines; rinsing of the bevel gears and ring
gear assist in preventing a buildup of debris that could
interfere with operating efficiency. CIP models can also be
equipped with the optional self rinse nozzle which washes
the exterior surfaces of the machine while it is operating.
Additional passages allow high pressure rinsing of internal
areas of the machine where deposits of solids could allow
bacterial growth. Drainage holes can be provided for
complete drainage of cleaning solution.
Nozzle Sizes
Nozzles are available in the following sizes:
1/4 in. | 6.35 mm. |
9/32 in. | 7.14mm |
5/16 in. | 7.94 mm. |
3/8 in. | 9.53 mm. |
7/16 in. | 7.94 mm. |
½ in. | 12.70 mm. |
9/16 in. | 14.29 mm. |
5/8 in. | 15.58 mm. |
0 Comments