MODEL 360 FLOW THROUGH 052820

Major VersionM

by Jason Wiseman

How to Assemble Model 360 Flow Through

Written By: Greg Whitener (and 3 other contributors)
  • Comments: 16
  • Favorites: 0
  • Completions: 3

Difficulty

Moderate

Steps

24

Time Required

Suggest a time??

Sections

1

Flags

0

Tools

Parts

  1. Collect Model 360, Flow Through, Parts

    • Collect Model 360, Flow Through, Parts

    Good picture

    Mike - Reply

    • Install Tee Housing Bearing 631 to Inlet Stem 603.

    • Seat Bearing 631 snugly.

    • Seat Tee Housing Seal 635-TG adjacent to Bearing 631.

    • Be sure spring is facing up.

    • Install Gearbox Screw O-Rings 641-3V to Inlet Stem 603.

    • Lubricate o-rings with non-petroleum-based lubricant.

    Good illustration

    Mike - Reply

    Recommendations:

    Show picture and details of 101 Kit, and pictures of 602-CST, 603-3ST, 623-ASTZ, 623-W, 637-BV and all O-Rings, 652-3, 654-S, 660-D

    Mike - Reply

    • Install Tee Housing Bearing Cup 632 to Tee Housing 604.

    • Use Cloud T3 tool.

    • Lubricate cups.

    • Be sure to seat cups completely.

    • Repeat for bottom side.

    Good -shows picture of tools needed

    Mike - Reply

    • Install Tee Housing 604 to Stem 603.

    • Be sure to seat Tee Housing completely.

    • Install Tee Housing Seal 635-TG between cup and stem.

    • Install spring side down.

    • Install Tee Housing Bearing 631 above Tee Housing Seal 635-TG.

    • Install Tee Housing Bevel Gear 617-S onto Bearing 631 matching notch to lug.

    • Install Ring Gear 620-SC matching notch to lug on Tee Housing 604.

    • Install Ring Gear Retaining Ring 621.

    • Install Gearbox Stem O-Ring 642-3.

    • Install O-Ring 662- onto 660-D

    • Install 660-D into Gearbox 601-3ST nose.

    • Lubricate all O-Rings.

    • Install Gearbox 601-3ST nose to center of Inlet Stem 603-3ST.

    • Align lug on Gearbox to pocket on Bevel Gear.

    • Be sure Gearbox is seated completely.

    • Screw holes on Stem must align with screw holes on Gearbox.

    • Install three Gearbox Bolts 650-3 with Gearbox Bolt Lockwashers 652-3.

    • Tighten with 3/8 nut driver.

    • Apply anti-seize to bolt threads.

    • Torque Gearbox Bolts 650-3 to 30 foot-pounds.

    • Use T5 tool to install Idler Shaft Bearing 627-T to Gearbox 601.

    • Bearing 627-T is the smallest Rulon/PTFE bearing.

    • Install O-Ring 639 to the 660-3A.

    • Lubricate O-Ring 639.

    • Use T5 tool to install 660-3A flush.

    • Flat side of 660 must face the largest hole.

    • PRO TIP! Before installing the gears, confirm that the A-Shaft will easily drop all the way down and spin freely.

    • Install Gear Assembly 616-SA-D to round opening in Gearbox 601-3ST.

    • Be sure assembly "Clicks" into place.

    • Install Gear Assembly 615 adjacent to Gear Assembly 616-SA-D with gears staggered.

    • Shaft 615-C will slide into Bearing 627-T.

    • Install Spacer 655-A to A-Shaft 622 and install A-Shaft 622 into Bearing 627-T.

    • Make sure gear teeth are engaged.

    • Install Rotor Thrust Shaft 626-AT to center cylinder bore.

    • Install Idler Shaft Lower Bearing 628-T to the midsize cylinder bore.

    • Install Final Shaft Lower Bearing 630-T to tallest cylinder bore.

    • Install Gearbox Cover O-Ring 644 to Gearbox Cover 602-CST.

    • Install Gearbox cover 602-CST to Gearbox 601-3ST.

    • Line up gear train shafts with Gearbox Cover bearings.

    • Tighten Bolts 646-AS with 7/16 nut driver. Torque to 100 inch pounds. (Bolts 646-AS are the larger of the two bolt sets.)

    • Use 647-s lock washers.

    • Lubricate O-Ring 644.

    • Do not disturb dowel pin!

    Good and excellent video

    Mike - Reply

    • Install Nozzle Housing Bearing Cups 634 to Dual Nozzle Carrier 605-S.

    • Press using T3 tool.

    • Lubricate cups.

    • Repeat for opposite side.

    • Install Nozzles 607-S to Nozzle Housing 605.

    • Use food grade anti-seize on threads.

    • Install Clutch O-Ring 637-B to groove in Nozzle Housing 605.

    • Install Nozzle Housing Bevel Gear 618-BS over Clutch O-Ring 637.

    • Install Bevel Gear Snap Ring 619.

    • Install Bearing 633 to Tee Housing 604.

    • Be sure to align "dots" on Bearing 633 and Tee Housing 604.

    • After Bearing 633 is seated, turn counter clockwise until it stops.

    • Install Seal 636-TG to Tee Housing 604 nose.

    • Be sure Seal 636-TG is flush to Bearing 633 with spring facing out.

    • Install Nozzle Housing 605-S to Tee Housing 604-AS .

    • Be sure gears are meshed.

    • Install Nozzle Housing Seal 636-TG spring down.

    • Be sure seal is seated completely.

    • Install Nozzle Housing Bearing 633 to Name Plate 606-CS.

    • Be sure "dot" on Bearing 633 and "dot" on Name Plate 606-CS are aligned.

    • Tighten Bolts 648-AS with torque wrench to 100 inch-pounds.

    • Bolts 648-AS are the smaller of the two bolt sets.

    • Use 647-S lock washers.

    • Install Rotor 610.

    • Lock using Lock washer 647-S and Rotor Retaining Nut 654-S.

    • Hold Rotor 610 with needle nose pliers to tighten Rotor Retaining Nut 654-S to 100 inch-pounds.

    • Install Stator 609-3S.

    • Install Strainer 664.

    • Install Stator Retaining Ring 645-3.

    Excellent -but don’t drop that NUT!

    Mike - Reply

  24. Finished! Good job!!

    • Finished! Good job!!

Finish Line

3 other people completed this guide.

Author

with 3 other contributors

Greg Whitener

Member since: 02/14/2017

961 Reputation

2 Guides authored

2 Comments

is there a video of how to take apart

santos meza - Reply

Excellent explanation step by step. Could you you make a video of the whole process?

eduadardo - Reply

Add Comment

View Statistics:

Past 24 Hours: 1

Past 7 Days: 3

Past 30 Days: 18

All Time: 2,188